If you require an alternate format of the following information, please contact our toll-free information line at 1-800-225-6972. In order to expedite your request, please have the document reference number or full title ready when placing your call. Return to the Main Document

CLICK THE APPROPRIATE LETTER TO GO
TO THAT SECTION'S REFERENCE LIST
5, 6, 7, 8, 9, 10, 11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the first letter of an author to go to that section.
|A |B |C |D |E |F |G |H |I |J |K |L |M |N |O |P |Q |R |S |T |U |V |W |X |Y |Z|

 

 

FINAL REPORT
WASTE PACKAGE MATERIALS PERFORMANCE
PEER REVIEW PANEL

5. REFERENCES

 Bethke, C.M., 1996, Geochemical Reaction Modeling, Concepts and Applications. Oxford University Press, New York, 397 pp.

Booth, W., 1987, "Postmortem on Three Mile Island," News and Comments Section, Science, Vol. 238, December, 1987, pp. 1342-1345.

Bowell R. J., 1994, Sorption of arsenic by iron oxides and oxyhydroxides in soils. Applied Geochemistry 9, 279-286.

Brossia, C. S., et al., Effect of Environment on the Corrosion of Waste Package and Drip Shield Materials , CNWRA 2001-03, Center for Nuclear Waste Regulatory Analyses, San Antonio, TX, September, 2001.

Broughton, K.R., R.L. Lafond, Z. Lewandowski, 2001, "Influence of Environmental Factors on the Rate and Extent of Stainless Steel Ennoblement Mediated by Manganese-Oxidizing Biofilms," Biofouling, Vol. 17(3), p.241.

 Carlos B. A., Chipera S. J., Bish D. L., 1993, Fracture-lining manganese oxide minerals in silicic tuff, Yucca Mountain, Nevada, USA. Chemical Geology 197, 47-69.

Civilian Radioactive Waste Management System Management and Operating Contractor, FY01 Supplemental Science and Performance Analyses, vol. 1, Scientific Bases and Analyses, TDR-MGR-MD-000007 Rev 00, Las Vegas, NV: Office of Civilian Radioactive Waste Management System Management and Operating Contractor, June 2001.

Cragnolino, G., Presentation to DOE Waste Package Materials Performance Peer Review Panel Meeting, Cleveland, OH, July 24, 2001.

 Davis, M.A., S. Martin, A. Miranda, J.M. Horn, 1998, "Sustaining Native Microbial Growth with Endogenous Nutrients at Yucca Mountain," LLNL Report No. UCRL-JC-129185.

Dexter, S.C., Ed., 1986, Proceedings: Biologically Induced Corrosion, NACE, Houston, TX.

Dexter, S. C. 1996. "Effect of biofilms on crevice corrosion," Proc. COR/96 Topical Research Symposium on Crevice Corrosion, NACE, Houston, TX, pp. 367-383.

Drever, J. L., The Geochemistry of Natural Waters, Prentice-Hall, Inc. (1997).

 Ehrlich H. L., 1996, Geomicrobiology. Marcel Dekker, Inc.

Eugster, H. P., Hardie, L. A., in Lerman, A. (ed.), Lakes: Chemistry, Geology, Physics, Springer-Verlag, New York (1978)

 Garrels, R. M., Mackenzie, F. T., in Gould, R. F., (ed.), Equilibrium Concepts in Natural Water Systems, Ch. 10, Am. Chem. Soc., Advances in Chemistry, 1967.

Gdowski, G. E., Presentation to the DOE Waste Package Materials Performance Peer Review Panel Meeting, Las Vegas, NV, May 23, 2001, BSC Graphics Presentations_YMGdowski_052301.ppt.

Green, R., Program Engineer at TMI responsible for MIC, Personal Communication, Jan. 15, 2002.

Greiss, J. C., Corrosion, 24, 96 (1968).

 Harrar, J., Carley, J. F., Isherwood, W. F., Raber, E., Report of the Committee to Review the Use of J13 Well Water in Nevada Nuclear Waste Storage Investigations, UCRL-ID-21867, Lawrence Livermore National Laboratory, Livermore, CA (1990).

Hoare, J. P. (1975). "A Kinetic Study of the Rest Potential on a Platinum|Oxygen Diaphragm Electrode." The Journal of Physical Chemistry 79(20): 2175-2179.

Hofstetter, K. J. and B.S. Ausmus, 1989, "The Identification and Control of Microorganisms at Three Mile Island Unit 2," Nuclear Technology, Vol. 87, pp. 837-844.

Horn, J.M., B.A. Masterson, A. Rivera, A. Miranda, M.A. Davis and S. Martin, 2002, "Bacterial Growth Dynamics, Limiting Factors and Community Diversity in a Proposed Geological Nuclear Waste Repository Environment," For submission to Geomicrobiology Journal.

Horn, J.M. and A. Meike, Eds., 1995, Report from the Workshop: "Microbial Activity at Yucca Mountain, Part I: Microbial Metabolism, Adaptation and the Repository Environment," LLNL Report No. UCRL-ID-122256.

 Leygraf, C. and Graedel, Atmospheric Corrosion, John Wiley & Sons, Inc., New York (2000).

 MacKinnon, R. J., Presentation to the NWTRB, June, 2001, BSC Graphics Presentations_YMMacKinnon_0620-2101.ppt.

Mankowski, J., and Szklarska-Smialowska, S., Corrosion Science, 15, 493 (1975).

Martell A. E. and Smith R. M., 1998, Critically Selected Stability Constants of Metal Complexes Database Version 5.0. National Institute of Standards and Technology.

 Pinhero, P.J., Materials Dept. Technical Group Leader, INEEL Research Center, Idaho Falls, ID, Personal Communication, Jan. 4, 2002.

 Reed, D.T., and R.A. Van Konynenburg, “Effect of Ionizing Radiation on the Waste Package Environment”, TIC # 234975.

Rosenberg, N. D., Gdowski, G. E., Knauss, K. G., Applied Geochem., 16 (2001) 1231-1240.

 Seinfeld, J. H. and S. N. Pandis, "Atmospheric Chemistry and Physics: From Air Pollution to Climate Change", John Wiley & Sons, Inc., New York, NY, 1998.

Stoecker, J.G., Ed., 2001, A Practical Manual on Microbiologically Influenced Corrosion, Vol. 2, NACE, International, Houston, TX.

 Wang, W., Pourbaix, A., Cebelcor RA, 13/R7 (1980)

Welch A. H., Westjohn D. B., Helsel D. R., and Wanty R. B., 2000, Arsenic in ground water of the United States: Occurrence and geochemistry. Ground Water 38, 589-604.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the first letter of an author to go to that section.
|A |B |C |D |E |F |G |H |I |J |K |L |M |N |O |P |Q |R |S |T |U |V |W |X |Y |Z|

Section

6. REFERENCES

 Baer, D.R. and M.J. Danielson, "Surface analysis and electrochemical studies of sulfur enhanced corrosion of nickel", J. Vac. Sci. Technol. A, 5 (4) (1987) p. 1147.

Berkowitz, B.J., and R.D. Kane, "The effect of impurity segregation on the hydrogen
Embrittlement of a high-strength nickel base alloy in H2S environments", Corrosion, vol. 36 (1980) p. 24.

Briant, C.L., Metall. Trans A, Vol 19A (1988) p. 137.

Briant, C.L., and K.L. Luthra, Metall. Trans.A, 19A (1988) p. 2099.

Brosia, C.S., L. Browning, D.S. Dunn, O.C. Moghissi, O. Pensado and L. Yang, "Effect
of Environment on the Corrosion of Waste Package and Drip Shield Materials", U.S. Nuclear
Regulatory Commission Contract NRC-02-97-009, Sept 2001, p. 3-35-36.

Burton, J.J., B.J. Berkowitz and R.D. Kane, "Surface segregation in an engineering alloy:
Hastelloy C-276", Metall. Trans. A, Vol. 10A (1979) p. 677.

 Cieslak, M.J., T.J. Headley and A.D. Romig, Jr., "The welding metallurgy of Hastelloy alloys C-4, C-22 and C-276", Metall Trans A vol. 17A (1986) p. 2035.

 Danielson, M.J. and D.R. Baer, "The effects of sulfur on the dissolution of nickel",
Corrosion Science, Vol. 29, (1989) p. 1265.

DOE Report, TDR-WIS-MD-000002 REV 00 ICN 02, December, 2000, p. 3-19.

DOE Report, TDR-MGR-MD-000007 REV00, June 2001, p. 7F-6,7.

 Heubner, U.L., E. Altpeter, M.B. Rockel and E. Wallis, "Electrochemical behavior and its
relation to composition and sensitization of NiCrMo alloys in ASTM G-28 solution",
Corrosion Vol 45 (1989) p. 249.

Hodge, F.G., H.S. Ahluwalia, "Influence of long-term low temperature aging on the
Performance of candidate high-nickel alloys for the nuclear waste repository"
Proceedings of the 12th International Corrosion Congress, Houston, TX, NACE
International, 5B (1993) p. 4031.

 Jones, R.H., S.M. Bruemmer, M.J. Danielson and B.D. Craig, "Austenitic Stainless
Steels", in Environmental Effects on Engineered Materials, R.H. Jones, Ed., Marcel
Dekker, Inc., New York, 2000, p. 31.

Jones, R.H., M.J. Danielson and D.R. Baer, "Role of segregated P and S in intergranular
stress corrosion cracking of Ni", in Corrosion of Nickel Base Alloys, R.C. Scarberry,
Ed., ASM Intl, 1985, p. 87.

Jones, R.H., and S.M. Bruemmer, "Environment-Induced crack growth processes in
nickel-base alloys", in Environment-Induced Cracking of Metals, R.P. Gangloff and
M.B. Ives, Eds., National Association of Corrosion Engineers, 1988, p. 287.

Luthra, K.L. and C.L. Briant, Oxidation of Metals, 26 (1986) p. 397.

 Raghavan, M., B.J. Berkowitz and J.C. Scanlon, "Electron microscopic analysis of
heterogeneous precipitates in Hastelloy C-276" Metall Trans A, Vol 13A (1982) p.
979.

Rebak, R.B. and N. Koon, "Localized corrosion resistance of high nickel alloys as
candidate materials for nuclear waste repository, Effect of alloy and weldment aging at 427 C
for up to 40,000 hours" Proceedings of the Corrosion 98 Conference, Paper No. 153,
Houston, TX, NACE International, 1998.

 Sridhar, N., J.A. Kargol and N.F. Fiore, "Effect of low temperature aging on the
hydrogen-induced crack growth in a Ni-base superalloy", Scripta Met., vol 14 (1980)
p. 1257.

 Tawancy, H.M.,"Long term aging characteristics of some commercial nickel-
chromium-molybdenum alloys", J. of Matl. Sci, Vol 16 (1981) p. 2283.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the first letter of an author to go to that section.
|A |B |C |D |E |F |G |H |I |J |K |L |M |N |O |P |Q |R |S |T |U |V |W |X |Y |Z|

Section

7. REFERENCES

 S. Boudin, J.-L. Vignes, G. Lorang, M.Da Cunha Belo, G. Blondiaux, S.M. Mikhailov, J.P. Jacobs and H.H. Brongersma, "Analytical and Electrochemical Study of passive Films Formed on Nickel-Chromium Alloys: Influence of the Chromium Bulk Concentration," Surface and Interface Analysis, v. 22, p.462 (1994).

 G. Lorang, N. Jallerat, K.Vu Quang and J.P. Langeron, "AES Depth Profiling of passive Overlayers Formed on Nickel Alloys," Surface and Interface Analysis, v. 16, p.325 (1990).

 B.G. Pound and C.H. Becker, "Composition of Surfcae Films on Nickel Base Superalloys," Journal of the Electrochemical Society, v. 138, p. 696 (1991).

 A.C. Lloyd, D.W. Shoesmith, J.J. Noel and N.S. McIntyre, "Effects of Temperature and Anodic Potential on the Passive Corrosion properties of Alloys 22 and C276," submitted for publication in Journal of the Electrochemical Society.

 G. Bellanger and J.J. Rameau, "Behavior of Hastelloy 22 Steel in Sulphate Solutions at pH 3 and Low temperatures," Journal of Materials Science, v. 31, p. 2097 (1996).

M. Bojinov, G. Fabricius, P. Kinnunen, T. Laitinen, K. Makela, T. Saario and G. Sundholm, "Electrochemical Study of the passive Behavior of Ni-Cr Alloys in a Borate Solution – A Mixed Conduction Model," Journal of Electroanalytical Chemistry, v. 504, p. 29 (2001).

 Gerald Gordon, "Waste Package Residual stress Mitigation Approach and Status," Presentation at Lawrence Livermore National Laboratory, January 23, 2002.

 G.Y. Lai, High Temperature Corrosion of Engineering Alloys, ASM International, Materials Park, OH (1990).

 W.Z. Friend, Corrosion of Nickel and Nickel-Base Alloys, The Electrochemical Society, John Wiley & Sons, NY (1980).

 P. Kritzer, N. Boukis and E. Dinjus, "Review of the Corrosion of Nickel-Based Alloys and Stainless Steels in Strongly Oxidizing Pressurized High temperature Solutions at Subcritical and Supercritical Temperatures," Corrosion, v. 56, p.1093 (2000).

P. Kritzer, N. Boukis and E. Dinjus, "Transpassive Dissolution of Alloy 625, Chromium, Nickel, and Molybdenum in High Temperature Solutions Containing Hydrochloric Acid," Corrosion, v. 56, p.265 (2000).

 S. Rajeswari, K. Suresh Kumar Danadurai, T.M. Sridhar and S.V. Narasimhan, "Surface Characterization and Pitting Behavior of High Cr-Ni-Mo Alloys in Simulated White Water Environemnt," Corrosion, v. 57, p.465 (2001).

 M. Pourbaix, Atlas of Electrochemical Equilibria in Aqueous Solutions," NACE, Houston, TX (1974).

 R.L. Cowan and R.W. Staehle, "The Thermodynamic and Electrode Kinetic Behavior of Nickel in Acid Solution in the Temperature Range 25°C to 300°C," Journal of the Electrochemical Society, v.118, p.557 (1971).

 L.J. Oblonsky and T.M. Devine, "Surface Enhanced Raman Spectra from the Films Formed on Nickel in the Passive and Transpassive Regions," Journal of the Electrochemical Society, v. 142, p. 3677 (1995).

 V. Schroeder and T.m. Devine, "SERS during the Galvanostatic Reduction of the Passive Film on Iron," Journal of the Electrochemical Society, 146, 4061-70 (1999).

 I.Olefjord, B. Brox, and U. Jelvestam, "Surface Compossition of Stainless Steels during Anodic Dissolution and Passivation Studied by ESCA," Journal of the Electrochemical Society, v.132, p.2854 (1985).

C.R. Clayton and Y.C. Lu, "A Bipolar Model of the Passivity of Stainless Steel: The Role of Molybdenum Additions," Journal of the Electrochemical Society, v.133, p.2465 (1986).

 A.R. Brooks, C.R. Clayton, K. Doss and Y.C. Lu, "On the Role of Cr in the Passivity of Stainless Steel," Journal of the Electrochemical Society, v.133, p.2459 (1986).

 C.S. Kumai and T.M. Devine, "Oxidation of Iron in Oxygen-Containing Water at 288°C," Corrosion 2001, Paper #01149, NACE, Houston, TX (2001).

C.S. Kumai and T.M. Devine, "Oxidation of Fe-Ni-Cr Alloys in Oxygen-Containing Water at 288°C," Corrosion 2001, Paper #01150, NACE, Houston, TX (2001).

 A.J. Davenport, J. A. Bardwell, C. M. Vitus, J. Electrochemical Society, v.142, 721 (1995).

 H. Chaung, J.B. Lumsden and R.W. Staehle, "Effecct of Segregated Sulfur on the Stress Corrosion Susceptibility of Nickel," Metallurgical Transactions A, v.10A, p.1853 (1979).

 D.A. Vermilyea, C.S. Tyedmon and D.E. Broecker, "Effect of Phosphorus and Silicon on the Intergranular Corrosion of a Nickel-Base Alloy," Corrosion, v.31, p.222 (1975).

 C.L. Briant, "Interfacial Segregation in Nickel Base Alloys: A Report to the Yucca Mountain Peer Review Panel," January 21, 2002.

 A.Turnbull, SME Report

 K. Mon, "Waste Package Degradation Studies at the Yucca Mountain Potential High-level Nuclear Waste Repository," YMP Senior Materials Science Panel Meeting, LLNL, January 24, 2002.

 R.S. Glass, G.E. Overturf, R.A. Van Konynenburg and R.D. McCright, "Gamma Radiation Effects of Corrosion – I. Electrochemical Mechanisms for the Aqueous Corrosion Processes of Austenitic Stainless Steels Relevant to Nuclear Waste Disposal in Tuff," Corrosion Science, v.26, p.577 (1986).

 D.D. Macdonald, "Passivity: The Key to Our Metals-Based Civilization," Pure and Applied Chemistry, v.71, p.951 (1999).

 R.A. Rapp, "High Temperature Corrosion Perspectives on Alloy Corrosion in the Burial of Radioactive Waste," Subject Matter Report, November 1, 2001.

T. Lian, J. Estill, G. Hust, D. Fix, C. Orme and J. Farmer, "Evolution of Corrosion Potential," YMP Senior Materials Science Panel Meeting, LLNL, January 24, 2002.

 S. Barnartt, "Linear Corrosion Kinetics," Corrosion Science, v.9, p.145 (1969).

 F. Mansfeld and K.B. Oldham, "A Modificatiion of the Stern-Geary Linear Polarization Equation," Corrosion Science, v. 12, p. 434 (1971).

F. Mansfeld, "Tafel Slopes and Corrosion Rates from Polarization Resistance Measurements," Corrosion, v.29, p.397 (1973).

D.D. Macdonald, "An Impedance Interpretation of Small Amplitude Cyclic Voltammetry," Journal of the Electrochemical Society, v.125, p.1443 (1978).

 R.L. Leroy, "The Range of validity of the Linear polarization Method for Measurement of Corrosion Rates," Corrosion, v. 29, p.272 (1973).

 K.B. Oldham and F. Mansfeld, "On the So-Called Linear Polarization Method for Measurement of Corrosion Rates," Corrosion, v.27, p.434 (1971).

 F. Mansfeld and M. Kendig, "Concerning the Choice of Scan Rate in Polarization Measurements," Corrosion, v.37, p.545 (1981).

 D.W. Townley, "Determination of aximum Scan Rtae for Linear Polarization Measurements," Corrosion, v.47, p.737 (1991).

 J.R. Scully, "Polarization Resistance Method for Determination of Instantaneous Corrosion Rates," Corrosion, v.56, p.199 (2000).

Summary of Recent Alloy 22 Corrosion Potential Data, Preliminary Predecisional Draft, June 21, 2001.

 C.Y. Chao, L.F. Lin and D.D. Macdonald, "A Point Defect Model for Anodic Passive Films, I. Film Growth Kinetics," Journal of the Electrochemical Society, v.128, p. 1187 (1981).

 L.F. Lin , C.Y. Chao and D.D. Macdonald, "A Point Defect Model for Anodic Passive Films, II. Chemical Breakdown and Pit initiation," Journal of the Electrochemical Society, v.128, p. 1194 (1981).

 C.Y. Chao, L.F. Lin and D.D. Macdonald, "A Point Defect Model for Anodic Passive Films, III. Impedance Response," Journal of the Electrochemical Society, v.129, p. 1874 (1982).

 M. Urquidi-Macdonald and D.D. Macdonald, "Transients in the Growth of passive Films on High Level Nuclear Waste Canisters," Proc. Int. Workshop Pred. Long-Term Corros. Behav. Nucl. Waste Systs., Cadarache, France, Nov. 26-29, 2001.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the first letter of an author to go to that section.
|A |B |C |D |E |F |G |H |I |J |K |L |M |N |O |P |Q |R |S |T |U |V |W |X |Y |Z|

Section

8. Bibliography

 Agarwal, D. C. (2000). Nickel and Nickel Alloys. Uhlig's Corrosion Handbook. R. W. Revie. New York, John Wiley and Sons: 831.

Arnvig, P. E. and A. D. Bisgard (1996). "Determining the Potential Independent Critical Pitting Temperature (CPT) by a Potentiostatic Method Using the Avesta Cell." Corrosion 96 Paper No. 437: NACE.

Arnvig, P. E. and R. M. Davison (1993). "Measuring Corrosion Resistance of Stainless Steels Using the "Avesta Cell" - Experiences and New Applications." Proc. 12th International Corrosion Congress, Houston, TX; Paper No. 209: 1477-1490.

ASTM (1995). G78-95, Standard Guide for Crevice Corrosion Testing of Iron-Base and Nickel-Base Stainless Alloys in Seawater and Other Chloride-Containing Aqueous Environments. Annual Book of ASTM Standards. Philadelphia, PA, ASTM. 3.02: 316.

 Barkatt, A. and J. Gorman (2000). Tests to Explore Certain Aspects of the Corrosion Resistance of C-22. Rockville, MD, ACNW Meeting.

Been, J. and J. S. Grauman (2000). Titanium and Titanium Alloys. Uhlig's Corrosion Handbook. R. W. Revie. New York, John Wiley and Sons: 863.

Brigham, R. J. and E. W. Tozer (1973). "Temperature as a Pitting Criterion." Corrosion 29(1): 33.

Brigham, R. J. and E. W. Tozer (1974). "Effect of Alloying Additions on the Pitting Resistance of 18% Cr Austenitic Stainless Steel." Corrosion 30(5): 161.

 Cotton, J. B. and B. H. Hanson (1994). Titanium and Zirconium. Corrosion. L. L. Shreir, R. A. Jarman and G. T. Burstein. Oxford, UK, Butterworth-Heinemann, Ltd. 1: 5:36.

Cragnolino, G. A., D. S. Dunn, et al. (2001). Corrosion Processes Affecting the Performance of Alloy 22 as a High-Level Radioactive Waste Container. Scientific Basis for Nuclear Waste Management. K. Hart, MRS.

Cragnolino, G. A., S. Mohanty, et al. (2000). "An Approach to the Assessment of High-level Radioactive Waste Containment. I: Waste Package Degradation." Nuc. Eng. and Des. 2001: 289.

 Dobson, D. (2001). FY01 Supplemental Science and Performance Analysis, DOE.

Dunn, D. S., G. A. Cragnolino, et al. (2000). "An Electrochemical Approach to Predicting Long-Term Localized Corrosion of Corrosion Resistant High Level Waste Container Materials." Corrosion 56: 90.

Dunn, D. S., G. A. Cragnolino, et al. (2000). Passive Dissolution and Localized Corrosion of Alloy 22 High-Level Waste Container Weldments. Scientific Basis for Nuclear Waste Management XXIII, Boston, MRS.

Dunn, D. S., Y.-M. Pan, et al. (1999). Effects of Environmental Factors on the Aqueous Corrosion of High-Level Radioactive Waste Containers- Experimental Results and Models. San Antonio, TX, Center for Nuclear Waste Regulatory Analyses.

Dunn, D. S., Y.-M. Pan, et al. (2000). Stress Corrosion Cracking, Passive and Localized Corrosion of Alloy 22 High Level Radioactive Waste Containers, NACE Corrosion2000.

 Evans, T. E. (1994). Nickel and Nickel Alloys. Corrosion. L. L. Shreir, R. A. Jarman and G. T. Burstein. Oxford, UK, Butterworth-Heinemann, Ltd. 1: 4:116.

 Farmer, J. (2001).

Farmer, J. C. and R. D. McCright (2000). General Corrosion and Localized Corrosion of Waste Package Outer Barrier, DOE.

Frankel, G. S. (1998). "Pitting Corrosion of Metals; A Review of the Critical Factors." J. Electrochem. Soc. 145: 2186-97.

Frankel, G. S. and R. C. Newman, Eds. (1992). Critical Factors in Localized Corrosion. Pennington, NJ, The Electrochemical Society.

Frankenthal, R. P. and J. Kruger, Eds. (1978). Passivity of Metals. Princeton, NJ, ECS.

 Gorman, J. (2001). Preliminary Tests Regarding Effects of Lead and Mercury on C-22 and Extrapolation to Service Conditions. Cleveland, Waste Package Materials Performace Peer Review Panel Meeting.

 Hibner, E. L. (1987). "Modification of Critical Crevice Temeperature Test Procedures for Nickel Alloys in a Ferric Chloride Environment." Mat. Perf. 26(3): 37-40.

 Isaacs, H. S., U. Bertocci, et al., Eds. (1990). Advances in Localized Corrosion. Houston, NACE.

 Kehler, B. A., G. O. Ilevbare, et al. (2001). Crevice Corrosion Behavior of Ni-Cr-Mo Alloys: Comparison of Alloys 625 and 22. RTS on Localized Corrosion. G. S. Frankel and J. R. Scully. Houston, NACE: 30.

Kehler, B. A., G. O. Ilevbare, et al. (2001). "Crevice Corrosion Stabilization and Repassivation Behavior of Alloys 625 and 22." Corrosion submitted.

 Laycock, N. J., M. H. Moayed, et al. (1995). Prediction of Pitting Potentials and Critical Pitting Temperatures. Critical Factors in Localized Corrosion II. P. M. Natishan, R. J. Kelly, G. S. Frankel and R. C. Newman. Pennington, NJ, ECS. PV 95-15: 68-78.

Leckie, H. P. and H. H. Uhlig (1966). "Environmental Fators Affecting the Critical Potential for Pitting in 18-8 Stainless Steel." J. Electrochem. Soc. 113: 1262-1267.

Lee, J. H. (2000). Abstraction for Models of Pitting and Crevice Corrosion of Drip Shield and Waste Package Outer Barrier, DOE.

 Macdonald, D. D. (2001). Presentation to NWTRB Workshop.

 Natishan, P. M., R. G. Kelly, et al., Eds. (1995). Critical Factors in Localized Corrosion II. Pennington, NJ, The Electrochemical Society.

 Pasupathi, V. (2000). Waste Package Degradation Process Model Report, DOE.

 Qvarfort, R. (1988). "New Electrochemical Cell for Pitting Corrosion Testing." Corros. Sci. 28: 135.

Qvarfort, R. (1989). "Critical Pitting Temperature Measurements of Stainless Steels with an Improved Electrochemcial Method." Corros. Sci. 29(8): 987.

 Rebak, R. B. (2001). personal communication.

Rebak, R. B. and P. Crook (1998). Improved PItting and Crevice Corrosion Resistance of Nickel and Cobalt Based Alloys. Critical Factors in Localized Corrosion III, A Symposium in Honor of the 70th Birthday of Jerome Kruger. R. G. Kelly, P. M. Natishan, G. S. Frankel and R. C. Newman. Pennington, NJ, The Electrochemical Society. PV 98-17: 289-302.

 Schutz, R. W. and J. S. Grauman (1986). "Corrosion bevavior of titanium and other alloys in laboratory FGD scrubber environments." Mat. Perf.(April): 35-42.

Sedriks, A. J. (1996). Corrosion of Stainless Steels. New York, Wiley-Interscience.

Shoesmith, D. W. (2000). Evaluation of the Candidate High-Level Radioactive Waste Repository at Yucca Mountain Using Total System Performance Assessment, Phase 5. Palo Alto, CA, EPRI: 5-1.

Shoesmith, D. W. (2000). Review of the Expected Behaviour of Alpha Titanium Alloys under Yucca Mountain Conditions, Atomic Energy of Canada, Ltd.

Shoesmith, D. W. (2001). Evaluation of the Long Term Stability of Passive Corrosion on the Waste Package and Drip Shield Under Yucca Mountain Repository Conditions, Electric Power Research Institute.

Shoesmith, D. W. and B. M. Ikeda (1997). The Resistance of Titanium to Pitting, Microbially Induced Corrosion and Corrosion in Unsaturated Conditions, AECL.

Sridhar, N. and G. A. Cragnolino (1993). Corrosion 49: 885.

Staehle, R. W., B. F. Brown, et al., Eds. (1974). Localized Corrosion. Houston, NACE.

Szklarska-Smialowska, Z. (1986). Pitting Corrosion of Metals. Houston, NACE.

 Turnbull, A., Ed. (1987). Corrosion Chemistry within Pits, Crevices, and Cracks. London, HMSO Books.

 Wilde, B. E. (1974). On Pitting and Protection Potentials: Their Use and Possible Misuses for Predicting Localized Corrosion Resistance of Stainless Alloys in Halide Media. Localized Corrosion. R. W. Staehle, B. F. Brown, J. Kruger and A. Agrawal. Houston, TX, NACE. NACE-3: 342-350.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the first letter of an author to go to that section.
|A |B |C |D |E |F |G |H |I |J |K |L |M |N |O |P |Q |R |S |T |U |V |W |X |Y |Z|

Section

9. REFERENCES

 Andresen, P. L. and Ford, F. P. 1994. "Fundamental Modeling of Environment Cracking for Improved Design and Lifetime Evaluation in BWRs." International Journal of Pressure Vessels and Piping, Vol. 59 (1-3), pp 61-70, Elsevier Science, New York, NY.

ANL-EBS-MD-000005 REV 00 ICN 01 (2000). "Stress Corrosion Cracking of the Drip Shield, the Waste Package Outer Barrier, and the Stainless Steel Structural Member," Revision 01, October 2000.

Andresen, P. L., Emigh, P. W., Young, L. M., and Gordon, G. M., "Stress Corrosion Cracking of Annealed and Cold Worked Titanium Grade 7 and Alloy 22 in 110°C Concentrated Salt Environments," Corrosion/2001, Paper 130, NACE International, Houston, TX, March 2001.

Andresen, Peter, 2001. DOE Waste Package Materials Performance Peer Review, "Waste Package Stress Corrosion Cracking Assessment and Strategy for Mitigation," May 23, 2001.

 Copson, H, R., 1959, Physical Metallurgy of Stress Corrosion Fracture, Interscience, p. 247.

Cragnolino, Gustavo, 2001 Response to question at a presentation to the DOE Waste Package Materials Performance Peer Review Panel Meeting, July 24, 2001, Cleveland, OH.

 Dunn, D. S., Pan, Y. M., and Cragnolino, G.A., 1999. "Effects of Environmental Factors on the Aqueous Corrosion of High-Level Radioactive Waste Containers – Experimental Results and Models," NRC Contract NRC-02-97-009, Center for Nuclear Waste Regulatory Analyses, San Antonio, TX, September 1999.

 Ford, F. P. and Andresen P. L 1988. "Development and Use of a Predictive Model of Crack Propagation in 304/316L, A533B/A508 and Inconel 600/182 Alloys in 288°C Water." Environmental Degradation of Materials in Nuclear Power Systems – Water Reactors, Proceedings of the Third International Symposium, Traverse City, MI, August 30 – September 3, 1987. Theus, G. J., and Weeks, J. R., eds. pp 798-800, Metallurgical Society, Warrendale PA.

 Gordon, G. M., 1977 "Physical Metallurgy of Fe-Cr-Ni Alloys," Stress Corrosion Cracking and Hydrogen Embrittlement of Iron Base Alloys, p. 893, NACE-5, National Association of Corrosion Engineers, Houston TX.

Gordon Gerald, 2000 NRC/DOE Technical Exchange on the Key Technical Issue: Container Life and Source Term, September, 12-13 2000, Las Vegas, NV, (Results to be Incorporated in WP PMR Revision).

 Parkins, R. N. 1977 "Environmental Aspects of Stress Corrosion Cracking in Low Strength Ferritic Steels," Stress Corrosion Cracking and Hydrogen Embrittlement of Iron Base Alloys, p. 601, NACE-5, National Association of Corrosion Engineers, Houston, TX.

 Roy, A. K., Fleming, D. L., and Lum, B. Y., 1998. "Stress Corrosion Cracking OF Fe-Ni-Cr-Mo, Ni-Cr-Mo, and Ti Alloys in 90C Acidic Brine," Corrosion/98, Paper 157, NACE International, Houston, TX.

Roy, A. K., and Freeman, D. C., and Lum, B. Y., 1999. "Stress Corrosion Cracking of Alloy C-22 and Ti Gr-12 Using Double Cantilever Beam Technique," Micron, Vol. 30, pp. 649-654, Pergamon, Elsevier, Science Ltd.

Roy, A. K., Fleming, D. L., and Freeman, D. C., 2000. "Stress Corrosion Cracking Evaluation of Candidate Container Alloys By Double Cantilever Beam Method," Corrosion/2000, Paper 00189, NACE International, Houston, TX.

 Sedricks, A. J., "SCC of Stainless Steels," Stress Corrosion Cracking, Materials Performance and Evaluation, pp. 91-130, ed. R. H. Jones, ASM International, Materials Park, OH.

 Thomas, L. E., Gertsman, V. Y., and Bruemmer, S. M., "Crack-Tip Microstructures and Impurities in Stress-Corrosion-Cracked Alloy 600 from Recirculating and Once-Through Steam Generators," Lake Tahoe Environmental Degradation Meeting, NACE International, Aug, 2001

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the first letter of an author to go to that section.
|A |B |C |D |E |F |G |H |I |J |K |L |M |N |O |P |Q |R |S |T |U |V |W |X |Y |Z|

Section

10. REFERENCES

 A.I. Asphahani, Paper. No. 42, Corrosion/78. NACE, Houston (1978).

A.I. Asphahani, Second Int’l Cong. on Hydrogen in Metals, Paper 3C-2, Paris (1977).

A.I. Asphahani and H.M. Tawancy in Corrosion and Corrosion Protection, p. 154. ECS, Pennington, 1981.

 B.J. Berkowitz and R.D. Kane, Corrosion, 36, 24(1980).

J. Blanchet, H. Coriou, L. Grall, C. Mahieu, C. Otter and G. Turluer in Stress Corrosion Cracking and Hydrogen Embrittlement of Iron-Base Alloys, p1149. NACE, Houston(1977).

 R.J. Coyle, Jr., J.A. Kargol and N.F. Foire, Met. Trans., 12A, 653(1981).

 G.E. Gdowski, UCRL-ID-108330, March 1991.

R.M. Latanision and H. Opperhauser,jr., Met. Trans., 5, 483 (1974).

R.M. Latanision, in Corrosion of Nickel-Base Alloys, p. 13. ASM, Metals Park (1985).

J.H. Shivley, R.F. Hehemann and A.R. Troiano, Corrosion, 23, 215(1967).

N. Sridhar, J.A. Kargol and N.F. Fiore, Scripta Met., 14, 1257(1980).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select the first letter of an author to go to that section.
|A |B |C |D |E |F |G |H |I |J |K |L |M |N |O |P |Q |R |S |T |U |V |W |X |Y |Z|

Section

11. REFERENCES

 G. S. Frankel, J. Electrochem. Soc., 145, 2186 (1998)

G. S. Frankel, in Passivity of Metals and Semiconductors; Vol. Proceedings Volume 99-42, edited by B. Ives, J. L. Luo, and J. R. Rodda (The Electrochemical Society, Pennington, NY, 2001), p. 445.

 N. G. Thompson and B. C. Syrett, "Relationship Between Conventional Pitting and Protection Potentials and a New, Unique Pitting Potential," Corrosion, Vol. 48, No. 8, 1992, p. 649.